RF up converters and RF down converters are integrated assemblies that convert RF and Microwave signals to another frequency range for further processing. Generally, they are designed to produce an output signal frequency for a particular frequency band. Synthesized devices use a synthesizer circuit (normally a PLL) to produce the desired LO frequency. This can be used as rack-mounted as well as designed to sit atop a table or desk

The C-Band up/down converter is a two channel RF system, one is up converter and other is down converter. The C-Band up/downconverter is designed to be used in satellite communication and aerospace application such as Tx and Rx for data transmission and reception in the C-band of frequencies .The downconverter converts 4.0 - 5.5 GHz to 70 MHz/140MHz and up converter converts from70 MHz/140MHz to 4.0 - 5.5 GHz.

  • Selectable bandwidth from 250 KHz to 40 MHz
  • Supports70MHz and 140MHz IF
  • Supports Remote Interface control
  • LCD Display for selected Frequency, Gain and Band width
  • Local/Remote selection switch
  • 1U 19” rack mountable, 10 kg max
  • 230 V AC Power supply
  • On board RF synthesizers
  • Low cost
  • <-60dbc spurious rejection
  • Cyclone II Controller
  • 10/100 BaseT Ethernet Interface
  • Max Output Power +10 dBm
  • Harmonic Rejection <-60dbc
  • Receiver Sensitivity -110 dBm
  • In-built Microstrip filters for better rejection

Up / Down Converter Common Specifications:

No. of Channels One(One RF and One IF)
RF Frequency 4000MHz-5500MHz, Programmable, 1MHz step size
IF Frequency 70MHz / 140MHz
Bandwidth Selectable – 0.25, 0.5, 1.0, 2.0, 5.0, 10, 20 & 40MHz(3dB BW)
Spurious/Harmonics response <-60dbc
Frequency Accuracy 0.002%
Phase Noise -110dBm typ at 100KHz
Return Loss Better than 10dB
Input / Output Impedance 50 Ω
Supply Power 230V
Remote Interface Ethernet
Size 1U 19” rack mountable, 10Kg max
Front panel Display for selected frequency, Gain, Bandwidth, IF / RF Output power control (switch/button) for Local / remote LED for power, local & remote Keypad / up / down / right left arrow for frequency, gain, bandwidth selection
Back panel Interface for power, Ethernet
Connectors (front panel) N (female) – RF input and output TNC (female) – IF input and output

Up-converter Specifications:

Input Level Range (IF) 0dBm to -80dBm
Output 1dB compression (RF) +10dBm
Output IP3 +20dBm
Gain -10dB to +80dB (adjustable)
Maximum Input Level +28dBm without damage
RF Output power detection To be provided

Down-converter Specifications:

Noise Figure 4dB Max
RF Input Level Range +10dBm to -100dBm
IF Output level +10dBm to -60dBm
Gain -30 to +60dB (adjustable)
Maximum Input Level +28dBm without Damage
AGC Slope and Range Programmable (-4 to +4V or 0to 10V)
IF Output Power Detection To be provided

Environmental Specifications:

Operating Temperature 0 to +70 deg C
Non-Operating Temperature -20 to +70deg C
Operating Humidity 0 to 90%
  • Test Bench Equipment
  • Satellite Communication
  • Radio relays
  • Wireless Local Loops

Contact Us

  • ELDAAS Technologies Pvt. Ltd.
  • 324, 2nd Floor
  • 1st Cross,Lal Bahadur Nagar
  • B.Channasandra, Kasturinagar
  • Bangalore, Karnataka, India
  • +91 80 4200 9090
  • +91 9739 696 999

© Copyright by ELDAAS Technologies Pvt Ltd. All rights reserved.                                     

A Customer Centric Innovative Product Solution and Services Company